How do you get the air out of a paddle board?
STEPS TO DEFLATE YOUR PADDLE BOARD When ready, remove safety cap and push down on the central valve head to release initial air. STEP 2: After approximately 15 seconds, push down all the way and twist the valve head clockwise to lock the air valve open for the remaining air to escape. Yes, inflatable paddle boards can burst, but this outcome is rare and typically the result of certain conditions or misuse. Over inflation, temperature variations, and material wear are the primary factors that could lead to a board bursting. Overinflation is the most direct path to a paddle board bursting.There is no rule saying you can’t leave your paddle board inflated; however, we strongly recommend that if you’re leaving your paddle board in storage for long periods of time, you should deflate it to keep it in its best possible condition.STEPS TO DEFLATE YOUR PADDLE BOARD When ready, remove safety cap and push down on the central valve head to release initial air. STEP 2: After approximately 15 seconds, push down all the way and twist the valve head clockwise to lock the air valve open for the remaining air to escape.There is no rule saying you can’t leave your paddle board inflated; however, we strongly recommend that if you’re leaving your paddle board in storage for long periods of time, you should deflate it to keep it in its best possible condition.If you leave your inflatable paddle board inflated while it’s in storage, your sup could succumb to over-expansion. Over-expansion occurs when there is too much air in the board, and the high internal air pressure causes the seams of the inflatable sup board to burst.
How to remove pump from paddle board without losing air?
The valve needs to be in closed position before you start pumping. You only open it when you want to deflate. Press the middle pin with your finger and twist. Then make sure you can’t deflate anymore by pressing the board. Then, you can plug and pump. The valve needs to be in the closed position which is done by putting the spring loaded pin in the up right position before you begin pumping to avoid the air coming out when you have finished pumping.Turn the SUP board valve stem to the CLOSED (UP) position. This may seem counterintuitive, but it works because a closed SUP valve has a rubber stopper on a spring that allows pressurized air to push through the valve while preventing air from coming back out.Most pumps have a lever that is down when it’s open and up to close. If your valve isn’t fitting into the hole, just flip the lever! Once it’s snug, go ahead and close up the pump — in most cases, this will mean lifting it up.
How to remove pump from paddle board without losing air?
Press and turn counterclockwise to the UP position. This activates the non-return valve and prevents air from escaping when you remove the pump hose. Turn the SUP board valve stem to the CLOSED (UP) position. If you leave the valve stem in the open position, you will lose all of the air pressure when you remove the hose.You can just let the board sit for a couple minutes and a lot of the air will push out on its own. If you would like to speed up the process and you don’t have an electric pump, you can just begin rolling and it will push the air out of the valve as long as it’s in the open position.As the board begins to inflate, the pressure gauge will start to move. Once the pressure gauge reaches between 12 and 15 PSI*, detach the pump hose from the air valve and replace the safety cap. If you’re looking for an upgrade from a hand pump, try out one of our Electric Pumps.
Is it okay to leave my paddle board inflated?
In summary, it is generally OK to leave your inflatable stand up board fully inflated, provided you follow the manufacturer’s recommendations and store it in a cool, dry place. The best inflatable stand-up paddle board PSI level is anywhere from 10 to 15. Most people inflate their board to about 10 to 12 PSI. A higher PSI will help if you are riding in cold or choppy water. If you need a bit more stability, try increasing the PSI of your board as well.While a SUP inflated to the recommended maximum PSI is unlikely to ‘pop’, it is good practice to keep a board out of prolonged contact with direct sunlight on hot days. Releasing a little air through the valve before leaving the board to stand may also be a useful precaution.Generally speaking, we’d suggest aiming for 15-22 PSI. This should ensure that your board reaches the levels of stiffness required for optimum stability, without you having to exert too much effort inflating your board or battle resistance from the valve when deflating it.